Category Archives: MB Star

  • 0

MB SD C5 SD Connect Compact 5 or SD Connect C4 Better?

MB Star Diagnosis C5 is an affordable & useful diagnostic and programming Tool For Mercedes Benz Cars & Trucks. Newly Mb Star C5 Wifi Mb Sd Connect Compact 5 supports wireless diagnose, Star Diagnosis SD C5 can support Mercedes BENZ car after Year 2000. MB SD C5 or SDConnect C4 how to choose? Below eobdtool.com share MB Star C5 compare with SDConnect C4, how to choose them.

MB SD C5 SD Connect Compact 5 or SDConnect C4 Better?

1. Most MB SD C5 Star diagnosis sd connect compact 5 is SD C4 inside about 400-420usd, prefer to get high-quality SD C4 for working.

2. Genuine MB Star Diagnosis SD Connect Compact 5 Clone comes with an HDD which installed software inside files you need.

3. The host communication connection end USES from design to avoid inadvertently fall in the normal use of the communication port to connect and communication failure,etc

Q : Are risk of using Mb Star C5 Wifi Mb Sd Connect Compact 5?
A: No,the operation is easy,pls take easy to use.

Q: Which Vehicle can MB Connect 5 compatibility with?
A: To be honest, Connect 5 can work well with almost all Mercedes BENZ cars,trucks after year 2000, see supported list below

4. SD C5 support DoIP of latest model after 2018, which support more function when you work on online programming.


  • 0

MB SD Connect 5 vs 2017 FVDI2 Commander

Both MB SD C5 and FVDI II are diagnostic and Programmer tools for Mercedes Benz Cars & Trucks.Then buy Mercedes Benz MB SD C5 or buy FVDI 2 Commander ,which better ? Referred to this question, here,the blog will make a comparison between these two tools,hope it will give you more informations.

About WiFi MB SD Compact 5

Newly MB SD C5 was updated from C4,compared to C4,the new SD Connect C5 with new design and better function and performance. And Car Diagnostic Tools MB SD Connect 5 is specially for Mercedes Benz Cars & Trucks after year 2000.

About 2017 FVDI2 Commander Diagnostic Tool

The 2017 FVDI2 Commander Diagnostic is a professional tool for fully programming your vehiles,see official features below

1. Read identification
2. Read extended identification
3. Read/Clear fault codes
4. Scanning for control units / Clearing fault codes in all control units
5. Display of Actual Values
6. Actuator Tests
7. Reset of control units
8. Control unit adaptations
9. Adjustment of injector injection quantities adaptation for Diesel Engines (CDI-4, CDI-5).

MB SD Connect 5 vs FVDI2 Commander

1.MB SD Connect 5 supports more Languages than FVDI II.

2.MB SD C5 Supports wireless diagnose,while the FVDI 2 didnt.

3.MB SD Connect C5 supports Mercedes Benz Cars After Year 2000,while the FVDI 2 can support Mercedes Benz Smart Maybach.

4. FVDI II Diagnostic Tool comes with a USB Dongle,the MB SD didnt.

5 FVDI II is a professional tool to programmer your vehicles from everysides like Airbag,Programming transponder keys ,Read/Write EEPROM of Dashboard control units and so on.

6. FVDI II Diagnosis can work on more window system than MD Connect C5.

7. 2017 FVDI II is expensive than MD SD C5.

So,if you are looking for a professional tool ,then buy FDVI II,though the price is expensive,yet,the function is powerful.But if you just wanna a tool to programming or flashing your Mercedes Benz,then buy MB SD Compact C5,currently,it is super hot and big welcomed.

See more click:http://www.autonumen.com/


  • 0

Benz C6 DOIP Xentry Diagnosis FAQ:

Benz C6 DOIP Xentry Diagnosis FAQ:

Q: Can Mercedes Benz C6 works stably? Is its quality good or not? Comparing with MB SD C4, it supports DoIP, what are more differences? Can it run faster than C4?
A: Benz C6 quality is good without problem.

Comparing C4, it has different hardware; it supports DoIP protocol and it can’t work with old Mercedes while sdc4 can support old Benz models if running fine with the old software.

The running speed depends on the computer configuration, the engineers are already tested C6 and C4 have almost the same running speed on a same computer.

Q: Is the C6 software is activated before delivery?
A: The software comes with Keygen so the users can activate by themselves. Because it is bound with a computer, if the supplier help active before delivery then the user has to active again after receiving.

Q: Does Benz C6 come with SCN coding function? or the user has to pay it?
A: It supports online SCN coding only when the user has online account.

Q: Can Benz C6 DOIP work with trucks?
A: yes, it works with trucks.

Q: Whether the window10 can be installed.
A: The software is preinstalled by allscanner Company, with win7 64bit.

Q: Whether the Korean language is supported when installing software is installed.
A: Yes, it has Korean language, besides more popular languages.

Q: The manual says that only one computer can be installed, but if I want to use it on two laptops, can I buy it from the Internet?
A: Like C4, it is hard disk version, it allows you to use on two laptops but needs to active by yourself with the built-in keygen.

Q: How to update when a program is updated.
A: To pay the newest software to update.

Q: I would like to know whether the coding method and usage method are on video or not
A: It has the same usage method as MB STAR C4.


  • 0

MB SD Connect C5 is Verified Working Great

The new Mercedes Benz diagnostic tool MB SD Connect C5 is
verified working great. Here are customer feedback to Benz C5
SD Connect (not original Xentry Connect C5).

1.
“Mercedes Sprinter year 2006 and 2014 works, both the
diagnosis
All the personal cars also works, no problem”
2.
“All the trucks including euro6 also works, no problem.
Bus Mercedes Tourismo euro5 year 2010-2012 test works, BUT
year 2014 euro6 does NOT work, it says that the license is
invalid. Both sd c4 and sd c5, we have tested both on the same
cars, to be sure.”
3.
SD Connect C5 this one customer has test, works good, in
function it no difference with SD C4, but performance it is
better. So you can buy MB SD C5 if you want buy new MUX. SD C5
use the same software as MB SD Connect C4.

“I have used V2016.12 software. I am ready to order the new 2017.05V software. It is said that the 2017.05 DAS/Xentry has improved a lot. New software in SSD runs faster and much more steable on Windows 7 or Windows 8 instead of Windows XP system. Also, new WIS and EPC parts catalog offers more full information for more models.
Well, my friend with 2016.12 version saying earlier Daimler AG needs the user name and password to login, but in this version, no need that.”


  • 0

MB SD Connect C5 is Verified Working Great

The new Mercedes Benz diagnostic tool MB SD Connect C5 is
verified working great. Here are customer feedback to Benz C5
SD Connect (not original Xentry Connect C5).

1.
“Mercedes Sprinter year 2006 and 2014 works, both the
diagnosis
All the personal cars also works, no problem”
2.
“All the trucks including euro6 also works, no problem.
Bus Mercedes Tourismo euro5 year 2010-2012 test works, BUT
year 2014 euro6 does NOT work, it says that the license is
invalid. Both sd c4 and sd c5, we have tested both on the same
cars, to be sure.”
3.
SD Connect C5 this one customer has test, works good, in
function it no difference with SD C4, but performance it is
better. So you can buy MB SD C5 if you want buy new MUX. SD C5
use the same software as MB SD Connect C4.

“I have used V2016.12 software. I am ready to order the new 2017.05V software. It is said that the 2017.05 DAS/Xentry has improved a lot. New software in SSD runs faster and much more steable on Windows 7 or Windows 8 instead of Windows XP system. Also, new WIS and EPC parts catalog offers more full information for more models.
Well, my friend with 2016.12 version saying earlier Daimler AG needs the user name and password to login, but in this version, no need that.”


  • 0

Instruction for Update and install V2.30 MB SD Connect C4 MUX

Good news! Star diagnostic firmware has come to the newest version V2.30 MB SD C4 with D-LINK WIFI Card, which is available at more compatible price. New mb sd c4 can read and clear fault code, read the live data of sensor and actuator, do coding and programming. And it supports wireless diagnose, K line,CAN BUS and UDS protocol.

Software version: 2015.07V
DELL D630 HDD/External HDD optional
SO106-B DELL D630 HDD
SS162-D7/S7 External HDD

Operating system:
Dell D630 format HDD on Dell D630 PC
External HDD needs PC with CPU 2.0GHZ or above, 4GB memory or more.

How to update new Star diagnosis MB SD Connect Compact 4 MUX to V2.30?

1. Please prepare 6 AA5 batteries according to Step-by-Step Instruction for how to install MB SD C4 Batteries.

Note: Please do use brand new batteries with sufficient electricity; otherwise, you will fail to update the firmware.

Then, select the green cable to connect to your laptop and MB SD Connect Compact 4 diagnostic multiplexer, and use OBD cable to connect to MB SD C4 multiplexer and your vehicle. (If the vehicle cannot be connected, select OBD 12V power instead.)

2. Open the software “2012.09 DAS”.
Go to C:\ program files \ SDconnect Toolkit to check whether there are the three following files as the pic below shows.
Update_automatic;
Update_manual;
Update_Special.
If the files’ names are different from the pic shows, please correct the names the same as the pic shows.

3. Restart your computer.

4. Start to update the firmware according to how to update MB SD connect4 MUX.

How to install V2.30 Star diagnosis MB SD Connect Compact 4 ?

1. Pls install it on XP system and close anti-virus software

2. This tool need to set your computer’s IP,you can see all installation


  • 0

How to update MB SD C4 Diagnostic Multiplexer

Here are the step-by-step instructions for updating the kernel software (operating system) on your Star Diagnosis MB SD Connect C4 multiplexer.
The kernel update of the SDconnect is similar to a regular software update via the Star Diagnosis system.

Step 1. Check battery if needed (only if related message is shown in the display)
When working on the vehicle or using an external power supply, the message “Batteries cannot be charged” may sometimes appear on the SDconnect display.
Note: The batteries had better be brand new to make sure of sufficient electricity.
Closing the Xentry Diagnostics/ Xentry DAS diagnostics application
When accessing a vehicle in Xentry Diagnostics or Xentry DAS, the following message appears

Exit the diagnostic application Xentry Diagnostics or Xentry DAS correctly to go on.

Step 2. Connecting the SDconnect to the Star Diagnosis system with the green cable

Step 3. SDnetControl
Start SDnetControl by clicking the deskband
Go to the “Connections” tab.
Check whether automatic selection via the cable connection is active

Go to the “Configuration” tab, and confirm the warning with “Yes”

Step 4. Software update

Go to the “MUX” tab in SDnetControl.
Click on the “Software update” button.

The “SDconnect Toolkit Administration” program will start.

Go to the “Software update” tab in the SDconnect Toolkit.
Your SDconnect is already selected on the left-hand side.
Select the “Software update” packet under “Files for software update”.
Click “Start” to start the process.

The update process will start. This takes approx. 4 minutes.
Step 5. Completing the installation
Confirm the successful completion of the update.
After a successful update, a message indicating the successful update completion appears.
Confirm the message by clicking “OK”.

Update not successful
If the update was not successful, the message “The software update was aborted. Please repeat the update process” will appear.
Confirm this message by clicking “OK”. Check the SDconnect batteries if necessary and repeat the update process.

The kernel update of the MB SD connect c4 is complete. The green cable can be removed.


  • 0

V2019.09 Mercedes BEZN MB STAR C6 MB SD Connect C6 OEM DOIP Xentry Diagnosis tool

Please note:C4, C5 software cannot be used for this product, this product must be used with our C6 software.If you don’t C6 software,please choose configuration 2
Mercedes Benz C6 OEM Xentry diagnosis VCI DOIP Pass thur interfac is the latest interface for For Mercedes & SMART vehicles can replace Star C4/C5. XENTRY Diagnosis VCI acts as a Pass-through Interface, also called MB Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the XENTRY software loaded on a PC.

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 Summary:
Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 (Vehicle Communication Interface) multiplexer serves as the interface to the vehicle when performing diagnosis and repairs, and programming electric and electronic on-board vehicle systems.

The Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 does not have its own PC core, battery, fan, or display. It is operated using the VXDIAG For XENTRY Diagnosis Pad via WLAN or a USB cable connection.
Notice:

If you choose hardware and software(500G HDD or SSD)

1. Please install the 500GB HDD(SSD) on laptop above 4GB Memory and I5 CPU, and use it on one laptop only.

2. There is keygen in our software HDD(SSD), no need activation by us.

3. This Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 can’t support All Key Lost,needs one key at least.
Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface Benz C6 Overview:
Compatible Software: VXDIAG For XENTRY/Das Software
Support Vehicle: Mercede For Benz & Smart vehicles
DoIP: Support DoIP
Functions: Star Diagnostic & programming (SCN Coding)

Mercedes Benz Xentry diagnosis VCI DOIP Pass thur interface C6 Features:
Can be used for all model series of For Mercedes For Benz vehicles
Support DoIP, cover more functions during SCN Coding than SD C4/C5
Functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
Diagnosis updates no longer necessary – firmware updates required on rare occasions
Does not need a power supply unit for external power supply
Dandy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
Engines (All Gasoline & Diesel Systems)
Transmissions and Electronic Selector Modules
Airmatic and Active Body Control Suspension Systems
Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
Drive Authorisation System
Sam (Signal Acquisition) Modules
Electronic Ignition System (EIS)
Pneumatic System Equipment and ATA functions
Air Conditioning / climate control Systems
Instrument Cluster
Tyre Pressure Control
Parktronic System
Keyless Go
D2b Command & Audio Gateway (D2B and MOST networks)
TV Tuner
Headlamp Range Adjustment
Seat Electronics
Rvc, RST & Vario Roof modules
Automatic Clutch System ACS
M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
Assyst & ASSYST + systems
What is DOIP?

DOIP is ISO 13400 diagnostic protocol
ISO 13400-1:2011 describes the general use cases and communication scenarios which are covered by an Internet Protocol-based vehicle communication standard. Each use case drives specific communication capabilities of the vehicle communication interface, for instance in order to be interoperable in an existing computer network.
The diagnostic communication over Internet Protocol (DoIP) protocol supports the standardized service primitive interface as specified in ISO 14229-2.
The descriptions in ISO 13400-1:2011 cover different application layer implementations, such as:
enhanced vehicle diagnostics (system diagnostics beyond legislated functionality, non-emissions-related system diagnostics);

WWH-OBD (World-Wide Harmonized On-Board Diagnostics) as specified in ISO 27145-2 and ISO 27145-3.
The mercedes Land Rover JLR all use this new Diagnostic Protocol now.
Where do you need DOIP device?

When we test mercedes new car like w222 w205
In Audio\Comand section you can find DoIP test page.

If cable is DoIP you will see green mark that DEVICE is Ok.


  • 0

Original Second Hand V2015.05 Mercedes BENZ C5 SD Connect Xentry Tab Kit Support Online Update

New arrived Original Second Hand Mercedes Benz C5 Xentry Connect

Most people have used C3 and C4 star for Benz vehicles , i want to recommed our Mercedes Benz C5 to all of you .

Please check the highlights of this device as bellow :
1.It support update online one year,latest version 2015.05
2.The present condition of the machine: 95% as new
3.Newest Mercede BENZ Diagnostic tool
4.With original software and tablet kit
5.Support newest hybrid W222

If you worried C3 and c4 can not satisfied your request , you can choose the original Mercedes Benz C5 , If you want to have a stable system to diagnostic your benz vehicle , please choose our C5 with tablet kit ,its Technical Parameters as following :
1.OS: windows 7
2.ultimate CPU:4G
3.Hard disk memory: 250G
4.13.3inch touch screen

BENZ C5 SD Connect Diagnostic Tool Main Features:
Efficient diagnostic program and complete vehicle database
Simple and easy-to-use user interface (UI)
High-performance Tab with 4G memory and 13.3 inch LCD touch screen
Advanced upgraded VCI+ communication interface
Support Wired/ wireless connection
Cover all new Mercedes Benz models.

Honestly speaking this equipment is very expensive , but the professional will know why it worth . For more details for this machine , please check on our store : www.autonumen.com


  • 0

V2017.9 Original Software Mercedes Benz MB SD C5 SD Connect Compact 5 Star Diagnosis with Engineer

Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.can work on windows xp, win7/8/10 system.

Xentry Connect C5 Benz SD Connect DoIP Wifi MB Star C5 Xentry Tab Kit Diagnosis Multiplexer
Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
The tool we sell do not include the xentry tab, you can equip one yourself or choose other laptop, it is just as a display, no special requirement.
Xentry Connect (VCI+) Technical Parameters:
1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
The way to connect: support wireless connection via 1000M workshop switches, also support wired connection.

What the difference on diagnostic systems based on Xentry Connect from other equipment used to diagnose Mercedes cars?
What are its distinguishing features?
Hardware, despite the similarity of many solutions with multiplexers SD Connect –
but the different All diagnostic software is loaded into the Xentry Connect multiplexer itself.
The management software can be installed on any computer with Windows 7 – 32-bit or Windows 8 – 32-bit and serves only for communication with the multiplexer
The licensing system is reworked – now licenses are stored on MB servers – Any license changes are tracked by the multiplexer when connected to the Internet network.
Why should buy Xentry connect
After 2015, all Star Diagnosis equipment is no longer supported. First of all, this means that there is no update of the diagnostic data for the newest cars and their systems, as well as the lack of the possibility of coding and programming of electronic units due to the backlog of the software data level in the device, from data in the electronic control units of the car.
Already at the end of 2014, at most dealerships, almost all of the previously used Star Diagnosis Compact4 with SD Connect DoIP multiplexers were almost completely removed. Instead, dealers received Xentry Kit kits, which include the latest Xentry Connect multiplexers and Xentry Tab tablets from Panasonic. Tablets are custom-made, although they also have a “civilian” version – the Panasonic Toughbook CF-D1,
somewhat inferior in terms of battery life to the original Xentry Tab, but it has a much more powerful configuration.
Honestly, the need to use the Xentry Tab on non-dealer services seems somewhat exaggerated to me. With dealers everything is clear – they were forced to use this equipment.
And what about workshop service? Undoubtedly, the tablet from Panasonic is not very bad … But … Its price is disheartening. The cost of the Japanese tablet is realistic to buy pieces of eight new laptops or tablets from other manufacturers.
So , we suggest buy Xentry connect from us , then buy a laptop yourself . the software from which Xentry Connect is managed can be installed without any problems on any computer that has a 32-bit version of Windows 7, Windows 8 or Windows 10. It’s clear with Xentry Connect itself – there’s no alternative .
After all, in this choice there are many reasons that encourage one to make a decision. The main thing is one: since 2015, the diagnostic multiplexer Xentry Connect C5 becomes the only one used at dealerships.
Thus, by purchasing this equipment, you do not lag behind the progress. You use in your work the best that is available today. Each your client, seeing with his own eyes that you in your work use the same device that he saw at the dealer’s service station, will understand that he made the right decision entrusting his car to your specialists.