Monthly Archives: March 2019

  • 0

Porsche PIWIS TESTER III

Allscanner VXDIAG Porsche Piwis III with Lenovo T440P Laptop  Porsche Piwis tester III V37.250.020

NOTE:
1.Allscanner VXDIAG Porsche Piwis III has the same functions with Porsche Piwis
2.If you want to do online programming,you must have an account online.
25.1
From autonumen.com VXDIAG Porsche Piwis III Functions & Features:
1.New operation system and more intuitive diagnostic interface
2.New VCI for post-2018 vehicles with DoIP diagnosis
3.Good at maintenance, repair, control units change and programming & setting codes
4.To login for online immobilizer programming
5.To find out leading faults
6.To look for maintenance wiring diagram
7.To support special functions like modification or flashing, with Engineering mode (Development version)
25.2
VXDIAG Porsche Piwis III New & Old Cars:
All Porsche from 1998-2018:
Porsche 911(997) (991)
Boxster/Cayman (987)
Cayenne up to MY 2010
Cayenne from MY 2011
Panamera

especially the latest models:
Paramera (971) 2018
Caynenne (92A) 2018
Macan (95B) 2018
911 (991) 2018
and other old models
25.3


  • 0

Porsche Piwis II V14. three hundred and fifty computer software Tester II

Porsche piwis tester 2 Help Devices:

SERP automatio tranny, air-conditioner, SRS, ABDOMINAL MUSCLES, ASR, MPL, GM, Authentic antitheft Program, KEYLESS MOVE program, OBDII program.
Porsche Piwis Tester II Options:

a single. Read/clear fault program code, snatch info supply, laptop or computer legitimate go with, component check, protection info consult, components site pulling, wires diagram.
two. For Porsche Piwis Tester ii works with this old and also latest for Porsche vehicles. This has this Panasonic laptop computer and also authentic computer software with the check. for Porsche Piwis Tester II can assist you analyze and also software probably the most different and also old variety for Porsche vehicles. As an example: 911(997)(991), Boxster/Cayman, (987), Cayenne as long as MY OWN the new year, Cayenne by MY OWN 2011 and also Panamera.
3 or more. Different Panamera might exclusively be diagnosed by making use of for Porsche Piwis Tester II. Based on recent job setting up, most of sooner car designs can little by little be improved onto the modern for Piwis Tester through the finish with the new year. For Porsche Piwis Tester I have to be applied for older designs within the for Porsche class until finally finish with the new year.
four. Help for Porsche. Porsche Piwis may don’t be on the market as soon as the earlier diagnostic routines have been transported for Porsche Piwis Tester II.
5 various. When for Professional Diagnostic Tools Porsche Piwis Tester II V14 can be sent out, it will consist of a single fundamental piece of computer software. It is necessary so that you can start and also configure this tester.


  • 0

Which mb sdconnect c4 worth the money?

MB SD connect C4 with laptop v2018.5 Version avaiable now ,It is ready to work after you get it ,worth to buy.

Star diagnosis SD C4 can used by wire connection or lan cable,everything set well before send it out .full chip .detail info.

1.Support Wireless

2.Software Version:2018.05

3. Hardware Verison:  OS:2.3   CSD:2.11

4.Serial number:100925
5. Supported Multi-Language: English/Bulgarian/Danish/Greek/Spanish/French/Italian/Korean/Polish/Romanuan/Serbo-Croatian/ Turkish/Czech/German/Finish/Hyngarian/Japanese/Dutch/Portuguese/Russian/Swedish/Chinese

6. Support Offline and Online Programming.

as we know ,it support wifi work,how to set it in WIFI condition ?

somebody do not know , but we know ,so we recommend buy with laptop together ,

so can use it directly when you get it .it’s worth to buy and save more time .Best feedback from here .

For further info.please use our online service www.autonumen.com or skype if you have .

Focus On OBD Tool Since 2008

Wechat/WhatsApp:(+86)15815514521

Email:service@autonumen.com

Website:www.autonumen.com


  • 0

CAT ET III WIFI Diagnostic Scanner Caterpillar ET3 Adapter III 317-7485

Heavy Duty Diagnostic CAT ET III WIFI Caterpillar ET3 Adapter III 317-7485 Diagnostic Scanner

CAT Communications Adapter III 317-7485 is the latest generation of the CAT Communication Adapter group, and replaces the CAT Comm Adapter II.This function is needed for some CAT ET (Electronic Technician) functions.

Real 2015A Caterpillar ET3 Adapter III P/N 317-7485 Professional Diagnostic Adapter for CAT with WIFI

This is the only recommended communication device for CAT, and the only datalink device that will allow you to properly communicate with a CAT engine on dual datalinks.

2015A Caterpillar ET3 Adapter III Communication:

1. Allows communication between service tools and engine controls using various data links such as J1939/11, DeviceNet (future release), CAT DataLink, and J1708 (ATA) vehicle networks;
2. Flash program allows adapter firmware upgrades as additional features become available;
3. Uses J1939/11, high-speed data link (part of ADEM III controls), substantially reducing flash times;
4. Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes).


  • 0

MB Star C5 Functions

The MB STAR C5 notion and brand combination for hardware and software program components will be the next step towards an integrated After-Sales Technique atmosphere with future-oriented diagnostic solutions.

Below the “XENTRY Solutions“ umbrella brand, users will now have access to XENTRY Diagnostics, XENTRY Strategies, XENTRY Flash and XENTRY Help & Feedback, as well as to the hardware diagnostic solutions XENTRY Kit and new Professional Diagnostic Tools such as XENTRY Control.
5.1
Autel Scanner MB Star C5 from Autonumen.com Functions:
1.can be modified as needed for each module
2.support for the latest models: W221, W212, W203, 211,204
3.Assistance HHT (Handheld Tester) MB Mercedes-Benz cars
4.professional digital full, partial, single diagnostic
5.Read and Clear DTC error code
6.Real (Real) sensor readings
7.Partial / single modules and complete diagnostic
8.Service time is reset
9.SRS, ABS, ASR, MPL, GM, speed control, engine diagnostic
10.keyless entry method
11.unlimited runtime without limitation, all vehicle classes open!
12.Disable automatic vehicle seat belt warning “subversive”
13.variants encoding in real time to any special features of the vehicle, activating existing SCN coding
14.read and write to the new SCN coding or functional modules Module Installation and Troubleshooting


  • 0

2019 Lonsdor K518S VS K518ISE

2019 Lonsdor K518S VS K518ISE:

The same: IMMO capabilities + Vehicle coverage.

The difference: The update subscriptions, Lonsdor K518S offers 3 optional subscriptions.

Lonsdor K518S:

1.SK213-B: Basic packagewith lifetime update
2.SK213-S1: fullpackage (free update for first 6 months) + one-year subscription(800USD)
3.SK213-S2: lifetime update subscription(not incl. the cost of hardware and basic package)

PDF: Lonsdor K518S function list

***

The parts with black words are free forever.

The red parts need money.

Lonsdor K518ISE (English version):

1.SK213: basic package (free lifetime)
2.SK213-S: one-year subscription(630USD)


  • 0

MB star c5 update newest software 2017.05

mb star c5 software update the newest version 2017.05,  mb star c5 is update version of mb star c4, it including all the mb star c4 function .

From autonumen.com mb star c5 Support Mercedes Benz Cars After Year 2000

it support vehicle list as following:

Passenger Car Support List:
A(176),  A(169),  A(168),  B(246),  B(245),  CLC(117),  C(204)  C(203),  C(202),  190(201),  E(212),  E(211),  E(210),  124(124),  S(222),  S(221),  S(220),  S(140),  S(126),
E(207),  CLK(209),  CLK(208),  CLS(218),  CLS(219),  CL(216),  CL(215),  CL(140)  SLK(172),  SLK(171),  SLK(170),  SL(231),  SL(230),  SL(129),  SL(107),  SLS(197),
M(166),  M(164),  M(163),  G(463),  G(461),  E(212),  E(211),  E(210),  124(124),  S(222),  S(221),S(220),  S(140),  CLK(209),  CLK(208),  CLS(218),  CLS(219),  CL(216),
CL(215),  CL(140),  SLK(172),  SL(231),  SL(230),  SL(129),  SL(107),SLS(197),  M(166),  M(164),  M(163),  G(460),  GL(164),  GLK(204),  R(251)

Van Support List:
MB 100(631),  T1,  SprinterIII,  SprinterII,  SprinterI,  Sprinter900,  Citan,  Vito(639),  Vito(638), V(638),   Viano(639),  T2,  Vario,  Vaneo(414)

Truck Support List:
Actros963/4,  Actros2,3,  AtegoIII,  AtegoII,  AxorII,  Eonic,  Zetros,  Actros,  Atego Light,  Atego Heavey,  HPN M96,  Atron,  HPN M2000,  SKL,  FSK,  Further model series

Unimog Support List:
U20,  UGN,  UHN

Bus Support List:
TRAVEGO,  INTOURO,  INTEGRO,  CITARO,  CAPACITY,  CITO,  TOURISMO,  O350/O403, CONECTO,  O404,  O405-O408,
Minibus,  OC500,  TOURO,  TOURINO,  MBC,  MULITEGO,  O500,  O500/OH,  OH,  OH368,  OF,  OF384,  LO,  O400,
FURTHER MODEL SERIES

Super Sports Car Support List:
SLR(199)


  • 0

Porsche Piwis Tester III with Panasonic CF54 Piwis3 PT3G Ver 37.250.020

Porsche Piwis Tester III with Panasonic CF54 Piwis3 PT3G Ver 37.250.020

Porsche Piwis Tester III is the newest fully operational diagnostic equipment based on PIWIS vehicle interface and Porsche software. Piwis Tester III provides exclusive support for Panamera G2, Cayenne E3 and all 2017 model range and above also provides legacy support for older models.

It is the new third generation Porsche diagnostic tool, it’s update to modern user interface, more faster performance, also have: license automatic update, online view of the technical documents, fault finding guide, online programming, faster and more efficient work.
14.1

Version: 37.250.020
License: Unlimited
Update: Via DVD or Online
Support Online Programming, no develop mode
Multi-Languages Add Slider WD
14.2

Porsche Piwis Tester III main functions
• General ECU diagnostics (DTC read/clear)
• Guided fault finding
• ECU programming/coding
• Real-time control parameters display
• Electrical schematics mapping

Porsche PIWIS 3 advantages
• Exclusive support for 2017 model range and above (Panamera G2, Cayenne E3)
• Fast and stable connection Simulation mode (diagnostic session without VCI connection)
• End user capable DVD update
• Wired USB connection


  • 0

John Deere Service Advisor with Nexiq clone 90% Worked

Topic 1:  John deere SA possible with Nexiq usb link?

It is possible to install John Deere Service Advisor on your laptop, though the installation is really complicated. If you have a Lenovo Thinkpad laptop, the easiest way is to restore the main partition from the image of my computers’ c: drive. And every time i change my laptop, i just restore it.

Win7 installed and fully updated. It takes hours.

The image will not work on xp, but SA works fine. My suggestion, buy used Lenovo T400 or T500. it’s more or less 250eur in europe. Install windows 7 and then can put my image. Takes 10 minutes and u have SA working.

Topic 2: How to get Nexiq china worked?
I spent a month doing research on this and i managed my Chinese NEXIQ to work 90%. The thing is that Nexiq has only 2 channels while EDL has 3. The 3rd one is Powertrain and it is used very seldom. E.g. I reprogrammed all the controllers on 6690 premium except two, but found a way around it opening the pld file with pldeditor and changing Powertrain channel to Vehicle (channel 1). Lots of machines don’t even have a 3rd Powetrain channel. Like all 5R; 6115R, 6125R, 7280R….. From my experience only the older machines have it and still can be programmed most of the time. Programming controllers is easy, but diagnostics is a bit annoying. Every time you establish the connection u have to remove the usb plug and plug it again for the readings to appear. Connection establishment is taking a long long time and you never see the ECU. Only all the other controllers. So all the time something doesn’t work. If you are prepared for this here is what you have to do:

a) Rewire the the cables as shown in the picture in my post here:

I switched places channel 1 with channel 2 (see the pic) with my Chinese version and now it works fine, probably it was possible to do it adjusting the software settings as mentioned above, but i tried a lot, and nothing helped. Now i can connect, tried with 6125R and 5070M. Works fine!!! Except one very important thingy. After i establish the connection, all the reading give the same meaningless number. Then, I discovered accidentally, I pull out the USB cable, get the message “Connection interrupted” I put it back in, get the message “Connection resumed” and wuolla, all the readings show up immediately.

b) You don’t have to change the firmware. Both will work pretty much the same but with different issues.

P.S. For diagnostics only, there is a subprogram of SA that works without any cable rewiring, it doesn’t have a Program Controller option, and you still need to reinsert the usb after connection has been established. You just need to select the right port (which is usually 1939Implement Autoboud or 1939App Autoboud depending on the machine) and model. If you have SA, you will find the software at c:\Program Files\Service ADVISOR\xvds\XJDET.exe
Just to let you know, after a year working like that, i bought another EDL (recommended by a folk in the forum, much much much more than the old one)
So much relief


  • 0

V2015A WIFI Wireless Cat et 3 Caterpillar communication adapter 3

WIFI Cat et 3 new arrival to Autonumen.com, software version v2015a cat et 3 adapter. Cat ET III with WIFI function replace common CAT ET 3 with Bluetooth. Caterpillar communication adapter 3 is the only recommended communication device for CAT.
Below Autonumen.com share you new arrival cat et 3 adapter.

Software version: 2015A

WIFI CAT ET 3 Highlight:

This is the only recommended communication device for CAT, and the only datalink device that will allow you to properly communicate with a CAT engine on dual datalinks

WIFI CAT ET 3 Recommended Configurations:

PC containing a 2.0 GHz dual-core processor
3GB RAM
3GB of available hard disk drive
DVD-ROM drive
15.4 inch XGA Screen (1280×1024 compatible)
Microsoft Windows™ 7 Professional or Windows 8 Professional (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 9 or newer is recommended.
Note: The most recent version of Microsoft Internet Explorer may not be validated to work with the service tool.

2015A Caterpillar ET3 Adapter III Communication:

1. Allows communication between service tools and engine controls using various data links such as J1939/11, DeviceNet (future release), CAT DataLink, and J1708 (ATA) vehicle networks;
2. Flash program allows adapter firmware upgrades as additional features become available;
3. Uses J1939/11, high-speed data link (part of ADEM III controls), substantially reducing flash times;
4. Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes).

This article is complied by Autonumen.com. For further information, pls feel free to let me know.

Focus On OBD Tool Since 2008

Wechat/WhatsApp:(+86)15815514521

Email:service@autonumen.com

Website:www.autonumen.com