Monthly Archives: January 2019

  • 0

Autel MaxiSys scanners big difference: MS908S Pro vs MS908P vs MS908

The main difference of Autel MaxiSys MS908S Pro, Autel MS908P and Autel MS908 is:

– Functions:

MS908S Pro and MS908P comes with J2534 ecu programmer so that both are able to do programming.

But MS908 only works for diagnostic tests for universal vehicles.

– Hardware:

The new Autel Scan Tool MS908S Pro is updated a lot in hardware design, which will run faster and much more stable to work with vehicles in tests.
2.1
2.2
2.3
2.4


  • 0

Porsche Piwis Tester 2 Online Coding Guide

Porsche Piwis online programming account service is piwis porsche subscription and piwis tester 2 online coding service offer via teamviewer. Porsche piwis coding account need to work with autonumen.com Porsche PIWIS tester 2 diagnostic tool. Porsche Piwis 2 online coding one time for one module of Porsche car coding.

Many customer inquiry about how to do online coding via piwis II, here we share Piwis II Online programming guide as following.

What need prepare for Piwis II online programming?

1.Original plan Porsche Piwis 2 inluded OBD & USB cable
2.Original XP system Piwis Tester II software running on laptop compatible with piwis II
3.One Porsche Car from 1996-2017 (vehicle support OBDII protocol )

If customer need original plan Porsche piwis II with laptop Piwis II software installed full set, just order here>>

14823129183 Porsche Piwis Tester 2 Online Coding Guide

When you keep all mentioned above ready for Porsche Piwis II online programming, just check and following below guide;

How does piwis II online coding service?

Step 1: Prepare Porsche Car information:

Excellent network performance is most important
Car model, Year
VIN number
What module need coding

Step 2: Order piwis II one time online programming here>>

Step 3: Due to time difference, pls keep your order number contact email sales@autonumen.com  appointment online programming available time in advance.

Step 4: Connect car to Porsche Piwis Tester and laptop, send us teamviewer id and password during appointment time for online coding service offering.

Step 5: Waiting for online programming till coding finished, and check and confirmed.

autonumen.com kindly note:

1. We do not offer Porsche Dealer Account login service.

2. We offer one time Piwis II online programming service from dealer account login till module coding be finished successful.

3. Piwis II online programming one time only for one module as usual, if customer need coding several module of cars, pls inquiry our sales for how many times Porsche piwis online coding service you need order.

With Porsche diagnostic tool online coding account, customers can activate the Porsche PIWIS tester2 vci online program function, any question about the Porsche piwis ii online coding account service just contact us freely.


  • 0

some inquiries about clone NEXIQ USB link 125032 adapter

NEXIQ USB Link is definitely the specialist Diesel Truck Diagnostic Adapter, it operate with almost Diesel truck models, here. vipprogrammer.com gather Some inquiries and troubles of Clone NEXIQ USB link 125032, possibly,   these FAQs will help you.

About some query and difficulty of NEXIQ 125032 USB link that our buyers meet. by means of these FAQ about NEXIQ 125032 USB, you’ll know extra data about NEXIQ 125032 USB, Hope this short article can assist you.

Q1: Can I update china clone Heavy Duty Diagnostic NEXIQ   USB link by internet? or upgrade new nexiq hardware?
A1: Sorry, china   NEXIQ 125032 USB link cannot be updated by internet, otherwise it will not operate.

Q2: Does NEXIQ USB   link application ought to be activated when i use it?
A: No, the all nexiq software is activated. the user manual and installation   guide also is included in the package, it can be simple to set up the software program.

Q3: does china clone Heavy Duty Truck Scanner NEXIQ USB link   can work on Volvo Bus and Isuzu truck? but discover that there is no communication among this two trucks models, what is the issue? What about CAT et diagnostic adapter?
A3:   NEXIQ USB link is not compatible with Volvo Bus, hardware will not help. Our Isuzu software is North American version. You could use it to perform on North American Isuzu. Nexiq will not be quite superior at diagnose CAT too. Specially for Asian Cat. Up to now, this Nexiq only help CAT with J1939 and J1708 protocol. But for Cat engine, generally protocol is CDL, it truly is specially for CAT models. For J1939 Protocol,   CAT model doesn’t use but.

Q5: When i set up the NEXIQ USB link application ready, i commence the engine, application prompt me error code 275.00, what is the meaning?
A6: The NEXIQ 125032 USB driver will not be installed correctly, so the application does not recognize the hardware. Please set up the USB driver once again.

Q6: When i use NEXIQ 125032 USB software connect using the truck, power and information light keeps flashing, what is wrong?
A6: it truly is the hardware error, probably, you update the device by web, Pls! don’t update it when you use it, you might want to send it back to us, we will repair it for you personally.

Q7: When i load Isuzu IDSS computer software, it failed. Along with the software offers me this error prompt: “CRC error: the file   C:Plan FilesIDSS images2007icvch processedfullsizefullb606.rra   doesnt match the file within the setup’s.cab file.”
A7: about this prompt of   NEXIQ 125032 USB link, possibly, it truly is brought on by two reasons:
1) You don’t use the correct strategy to load this software program, stick to the user manual to perform it;
2) The operation system does not compatible with this software.

Q7: When i open the NEXIQ USB link software program, i meet this dilemma: “Unable to study value softwareMack Trucks, IncCommonDevice ID”. Very first i opt for “Preferences”, next “RP123A Device name”, then i locate XTruck USB inside the drop down box. Why this happen?
A7: about this error of NEXIQ USB link on Autonumen.com, perhaps, it can be triggered by the following two cause:
1) USB driver is not installed correctly. Check your driver installation and set up the patch file of the CD.
2) other people application isn’t compatible with this computer software on your computer, or you have set up other individuals version NEXIQ 125032 USB software program on your laptop or computer ahead of. Adjust an additional computer to install the application again, or clearn your computer.


  • 0

CAT ET III Caterpillar Scanner Features

CAT ET III Caterpillar Scanner Features:

Display graph and log status parameters.
Retrieve prognostic data including histograms, engine totals for fuel used and miles traveled.
View active diagnostics and clear logged diagnostics. View events where irregularities have occurred and have been logged by the ECM.
Perform calibrations to enhance performance of the ECM.
Customize the ECM with application-specific settings.
Over 100 custom Diagnostic, Information and Service features including:
2D and 3D Histogram plotting capability (engine software support required).
Custom Status screen groups
Snapshots (Download and display snapshot data recorded by the ECM)
Configuration Aid that allows upload/download of same configuration to multiple control modules
Customised Service Tool Options
Customized service tool name
Customized graphics for the splash screen and icons
Customized installation
Aftermarket differentiation, the tool for one customer does not work on the product of another customer.
Licensing options for customer management
Flash programming of the ECM(s)
Training demonstration allows familiarity with the toola s primary functions without connecting to ECM(s)
Major operating systems support (Microsoft Windows 95, 98, NT 4.0, 2000, ME, & XP)
Perform customized diagnostic tests to identify harness problems, cylinder or component failures (Automatic Cylinder Cutout with cylinder to cylinder fueling comparison)

CAT ET 2015A Software:

Designed to run with Microsoft Windows 95, 98, 2000, NT and XP

Ready to use, just install software program onto PC using provided CD

The PC-based service tools from Caterpillar provide the capability to access Electronic Control Modules (ECMs) from a personal computer. Many job-critical tasks can be performed with an electronic service tool.

The user can display the status of a group of parameters (temperatures, pressures, etc.) simultaneously, view active and clear logged diagnostics, display the current configuration of an ECM and much more.

The service tool works with a communication adapter to allow connection to an ECM. A graphical interface makes this software quick to learn and easy to use. A separate pull-down menu for each function enhances the a??ease of use.a?? The version and identification of the ECM is automatically retrieved and is displayed on a summary screen when the program is started.

Diagnostic tests and calibrations can also be performed.
Caterpillar PC-based tools enable service technicians to reprogram ECMs, reconfigure control system parameters, fine tune performance or diagnose the root cause of a failure the first time. These powerful tools allow service personnel to display and analyze vital performance and health information from any system quickly and accurately.

The service tool communicates with any system using ATA (J1708), J1939 or the Caterpillar proprietary data link networks. The service tools provide information and features needed to help a technician diagnose problems and perform repairs and to customize and personalize the operation of a product.

By allowing customers to design flexibility and configurability into a product, Caterpillar service tools stretch beyond the capabilities of preprogrammed ECMs or onboard display systems.

Software version: 2015A

2015A Caterpillar ET3 Adapter III Communication:

1. Allows communication between service tools and engine controls using various data links such as J1939/11, DeviceNet (future release), CAT DataLink, and J1708 (ATA) vehicle networks;
2. Flash program allows adapter firmware upgrades as additional features become available;
3. Uses J1939/11, high-speed data link (part of ADEM III controls), substantially reducing flash times;
4. Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes).


  • 0

(Solved) John Deere Service Advisor Search Engine Error

This is for anyone when he/she runs the John Deere Service Advisor heavy duty diagnostic software, the system appears error message that the search engine module can not be loaded and then the program ends.

NOTE THAT YOU ARE TRYING ANY TRICK ON YOUR OWN RISK.

Optional solutions:

Solution 1:

Run as system administrator, roll back pc date reactivate using activator Then roll date back to normal date if error still renew once again. Been working for me so far.

Note that, don’t know how long it stay working but works im sure someone will have solution for it soon.

Also advice if doing fresh install roll back the date on pc do the install after then install and activations have been done.
Go to task manager look for the service adviser on have it start its tasks in 2030 :save and then reset your pc date should be good for while

Solution 2:

if you set a date before the lightweightidol license expired, start the lightweightidol service, set the real date and start Advisor, it works.

Solution 3:

start advisor. when error comes with “search engine” Close John Deere SA. afterwards set your PC date to feburary 2015. start SA again (run as administrator). it now comes with error on licence. close SA Again. set pc date back to normal. run SA Again. now it Works.

Solution 4:

The search engine error can be solved.
Set back the date, before the expiry date found in Service ADVISOR\SUIR\license.log (august 14 in my case). Start LightweightIDOL service. Set the real date, and Advisor working again.
I made a batch file to simplify it. To make it work Control Panel/Regional/short date format have to be yyyy-mm-dd or you have to modify batch. Maybe you have to modify ServiceADVISOR.exe path too in the batch. Have to run as administrator.

Solution 5:

I have had the same error with ssearch engine connection in JD SA.
reinstalled it twice, changed system date back and forward, run activator. No result for me.

But actually I found the solution for this issue.

Solution 6:

back date to 08.10.16
install JD SA, restart, activate, mount latest disk you have (05.2016) and install update, for finish get license error, ignore and close, set actualy date, run JD SA -> works fine, install july update

testing today on 3 laptops (Windows 7 and 10)

On a side note: procedure about turning off the updates don’t know how long it stay working but works im sure someone will have solution for it soon.

Also advice if doing fresh install roll back the date on pc do the install after then install and activations have been done.
goto task manager look for the service adviser on have it start its tasks in 2030 :save and then reset your pc date should be good for while Smile (SO TURN IT OFF IN TASKMANAGER SO IT STARTS 20 30 YEARS FROM NOW!!)

Fresh new installations also work but can be much more complicated sure a patch would be much easier. But it can be done with out a patch so far

In taskmanager I don’t stop any service just put service advisor updater to 2030 to start

also makes sure eculp.ini configurator reads like this

A valid ECULP License has been found

Licenses for the following modes have been found:
TestCell Programming
FinalEOL Programming
Service Programming
ECUCPP Programming Tool

All JD Components were found and properly licensed

JDEcu : Version 1.0 : 01-apr-2021
JDConfig : Version 1.0 : 01-apr-2021
JDData : Version 1.0 : 01-apr-2021
JDIntelHex : Version 1.0 : 01-apr-2021
JDPayloadReader : Version 1.0 : 01-apr-2021
JDPayloadProcessor : Version 1.0 : 01-apr-2021
ECULoaderProgram : Version 1.0 : 01-apr-2021
ECULP_TestCell : Version 1.0 : 01-apr-2021
ECULP_FinalEOL : Version 1.0 : 01-apr-2021
ECULP_Service : Version 1.0 : 01-apr-2021
ECULP_TestCell_OEM : Version 1.0 : 01-apr-2021
ECULP_FinalEOL_OEM : Version 1.0 : 01-apr-2021
ECULP_Service_OEM : Version 1.0 : 01-apr-2021
ECULP_ECUCPP : Version 1.0 : 01-apr-2021
ECULP_Direct_EOL_Output : Version 1.0 : 01-apr-2021
ECULP_OEM_DISTRIBUTOR : Version 1.0 : 01-apr-2021
Service_ADVISOR_Ag : Version 1.0 : 01-apr-2021
Service_ADVISOR_CF : Version 1.0 : 01-apr-2021


  • 0

FAQ MB Star C3 Diagnostic Tool

MB Star Diagnostic Tools MB Star C3 Diagnostic Tool 2015.03 is a professional and excellent diagnostic tool for trucks and new types of cars. This version of MB STAR C3 can fit all computers which is not only limited on IBM T30, to provide great convenience to customers. MB Star C3 Multiplexer has one hard disk contain DAS and WIS system.

Many customers meet lots of problems and do not know how to solve when using MB Star C3. This article will focus on this point.

From Autonumen.com MB Star C3 Diagnostic Tool For BENZ Truck and Cars has past truck test and can be used to do Benz trucks.

1Q: How to do MB Star C3 self diagnostic?

A: Please follow the next instruction to do self diagnostic.

Step 1. Click “STAR UTILITIES”

Step 2. Enter “Star Utilities”, click “Self Diagnosis” and then click “Caesar Self Diagnosis”.

Step 3. The self-test has started, please wait.

Step 4. This is Self-diagnostic report

2.Q: Star C3 got error reading: StarUtils Save not successfully-licCheckLicense XENTRY Diagnostics

4 – StartKey can not be decoded or scheme is not recognized, or appID unknown.

A:

1. “Xentry can’t active, save not successfully”?

Step1. Please reset your computer date to a specific date that three months later than the C3 version (for example, if the C3 is 2013.05, then the computer date should be reset to 2013.08. 2). Step 2. Please activate again. There is a .pdf file named [Open your Star 2013.05] on the C3 operation window, which step-by-step shows how to activate MB star and also we have video demo at

column.

Step 3. If it still can’t be activated after you reset the computer system time, please go to Local Disk (: C) and delete [lic-key2]. Then try to active again.

2. StartKey can not be decoded or scheme is not recognized, or appID unknown?

Please restart your computer or wait for a longer time, and it will display as follow:

3.Q: When I active Xentry, the [Start date] is not as the same as the date you give me, does it need to set time firstly?

A: You only need to set the computer system date. The [Start Date] and [Finish date] is set by us, so just ignore them.

4.Q: I connect Star C3 to the car and the computer, the COM port is also set, but I got the following error.

A: Firstly try to do a self-diagnostic to see whether Star C3 is connected well with the computer and the car, whether it has communication between Star C3 and the software driver or whether the settings is correct. Then according to the self-diagnostic report, you can reset the incorrect operation.

Published on mb star c3


  • 0

BMW ICOM

BMW ICOM is Professional  diagnostic tool for BMW group vehicles.BMW ICOM A2 is upgrade of BMW ICOM, and it’s always next technology of BMW ISTA diagnose and programming product. BMW ICOM A2+B+C has functions as follow: A2 – OBD diagnostic supporting MOST, D-CAN and K-CAN protocols; B – diagnostic via MOST bus, and possess link to A-interface through USB connection; C – 20-pin cable for previous types.
30% Discount Products BMW ICOM A2 Compared with ICOM:
1. The modified ICOM A2 for vehicles with OBD access receives a significantly more powerful processor and more storage capacity.
2. Robust aluminium case will help to avoid damage when using in harsh environments.
3. To protect the MOST connector, the ICOM B for vehicles with optical MOST access will be equipped with a soft cover made of rubber instead of the former plastic cap.
4. The ICOM C for old series with a diagnostics socket will be additionally equipped with an approx. 20 cm long cable, which facilitates the connection of the ICOM A2 and makes storage in the engine compartment easier.
5. BMW ICOM A2+B+C support BMW cars till 2013 year. Support BMW & MINI full system diagnose and offline programming.


  • 0

a variety of queries related to clone NEXIQ USB connection 125032 adapter

NEXIQ USB Link Connection is unquestionably the actual specialist Diesel Vehicle Diagnostic Adapter, it work together with virtually Diesel vehicle models, these. vipprogrammer. com assemble Quite a few queries as well as problems of Clone NEXIQ USB connection 125032, possibly, these kind of Frequently asked questions will assist you to.

Related to a variety of question as well as difficulty of NEXIQ 125032 USB connection which our prospective buyers satisfy. in these kind of FAQ related to NEXIQ 125032 USB, youll recognize further files related to NEXIQ 125032 USB, Desire this information may help everyone.

Q1: Should i up-date china clone NEXIQ USB connection simply by world wide web? or even enhance brand new nexiq computer hardware?

A1: Sorry, china Heavy Duty Diagnostic NEXIQ 125032 USB connection can not be updated simply by world wide web, otherwise it’s going to not really work.

NEXIQ 125032 USB connection

Q2: Should NEXIQ USB connection practical application need to be running after i apply it?

Some sort of: Very little, the actual just about all nexiq software program is usually running. the consumer manual as well as installation guide is also included in the package, it usually is easy to setup the actual software program.

Q3: should china clone NEXIQ USB connection can work on Volvo Bus as well as Isuzu vehicle? nevertheless discover that there isn’t a verbal exchanges between this particular two trucks models, is there a situation? What about KITTEN et diagnostic adapter?

A3: NEXIQ USB connection just isn’t appropriate for Volvo Bus, computer hardware will never guide. Your Isuzu software program is usually North U . s . model. Make use of it to do at North U . s . Isuzu. Nexiq will not be fairly top-quality at spot KITTEN far too. Exclusively regarding Asian kitchenware Kitten. So far, this particular Nexiq just guide KITTEN together with J1939 as well as J1708 standard protocol. Nevertheless regarding Kitten motor, in general standard protocol is usually CDL, it definitely is usually exclusively regarding KITTEN models. Regarding J1939 Standard protocol, KITTEN model doesnt apply nevertheless.

Q5: After i create the actual NEXIQ USB connection practical application completely ready, my partner and i continue the actual motor, practical application prompt me error signal 275. 00, is there a this means?

A6: The actual NEXIQ 125032 USB airport taxi driver will not be put in appropriately, and so the practical application doesn’t recognize the actual computer hardware. Remember to create the actual USB airport taxi driver as just stated.

Q6: After i apply NEXIQ 125032 USB software program connect using the vehicle, electric power as well as data easy continues pulsating, what is erroneous?

A6: it definitely will be computer hardware error, most likely, everyone up-date the 780 simply by world wide web, Pls! dont up-date it by using it, you should send it returning to all of us, we’ll do the repair suit your needs.

Q7: After i weight Isuzu IDSS computer software program, it broke. And the software program delivers me this particular error prompt: CRC error: the actual file D: Package FilesIDSS images2007icvch processedfullsizefullb606. rra doesnt fit the actual file inside the setups. pickup’s cab file. 

A7: about this prompt of NEXIQ 125032 USB connection, possibly, it definitely is usually attributable to two causes:

1) Everyone dont create a savings fund proper strategy to help weight this particular software program, go by the consumer manual to do it;

two) The actual function process doesn’t appropriate for this particular software program.

Q7: After i available the actual NEXIQ USB connection software program, my partner and i satisfy this particular difficulty: Unable to help review cost softwareMack Trucks, IncCommonDevice ID. Primary my partner and i go for Preferences, next RP123A Machine name, and then my partner and i find XTruck USB inside the fall decrease proverbial box. Precisely why this particular come about?

A7: about this error of NEXIQ USB connection, possibly, it usually is triggered with the following two trigger:

1) USB airport taxi driver just isn’t put in appropriately. Look at ones airport taxi driver installation as well as create the actual garden file with the DVD.

two) some people practical application isnt appropriate for this particular computer software program on your hard drive, or even you’ve got create different people today model obd2 tool 125032 USB software program against your computer or even computer in advance of. Fine-tune an additional computer to set up the approval all over again, or even clearn your computer.


  • 0

CAT ET III WIFI Diagnostic Scanner Caterpillar ET3 Adapter III 317-7485

Heavy Duty Diagnostic CAT ET III WIFI Caterpillar ET3 Adapter III 317-7485 Diagnostic Scanner

CAT Communications Adapter III 317-7485 is the latest generation of the CAT Communication Adapter group, and replaces the CAT Comm Adapter II.This function is needed for some CAT ET (Electronic Technician) functions.

Real 2015A Caterpillar ET3 Adapter III P/N 317-7485 Professional Diagnostic Adapter for CAT with WIFI

This is the only recommended communication device for CAT, and the only datalink device that will allow you to properly communicate with a CAT engine on dual datalinks.

2015A Caterpillar ET3 Adapter III Communication:

1. Allows communication between service tools and engine controls using various data links such as J1939/11, DeviceNet (future release), CAT DataLink, and J1708 (ATA) vehicle networks;
2. Flash program allows adapter firmware upgrades as additional features become available;
3. Uses J1939/11, high-speed data link (part of ADEM III controls), substantially reducing flash times;
4. Automatically selects J1939/11 when flashing the engine (reduces the flash time approximately 80%, from 14 minutes to 3 minutes).


  • 0

How to update Nexiq firmware with John Deere SA

When I was doing experiments with my Nexiq clone (also called Xtruck) and John Deere Service Advisor(JDSA)…

Running the utility binload from the folder C:\Nexiq\Test.
Set checkbox – Enable automatic USB-Link firmware upgrade
and get firmware bin file.
Save original bin with other name (for recovery).

I copy the firmware bin from the program John Deere SA,
rename as original Nexiq bin name
and replace original – by that file.

Next, again start utility binload from the folder C:\Nexiq\Test
and have John Deere SA firmware in Nexiq.

I have test connection with 2CAN pin and read engine serial
but i don’t run program…
I could not do normal work program…

JDL adapter like Nexiq adapter…
In Nexiq new driver have new firmware version
I always update firmware and do not have problem…
Credits to Dmitry in the MH community